Creates a new #NMSettingWired object with default values.
When %TRUE, setup the interface to accept packets for all MAC addresses. This is enabling the kernel interface flag IFF_PROMISC. When %FALSE, the interface will only accept the packets with the interface destination mac address or broadcast.
When %TRUE, enforce auto-negotiation of speed and duplex mode. If "speed" and "duplex" properties are both specified, only that single mode will be advertised and accepted during the link auto-negotiation process: this works only for BASE-T 802.3 specifications and is useful for enforcing gigabits modes, as in these cases link negotiation is mandatory. When %FALSE, "speed" and "duplex" properties should be both set or link configuration will be skipped.
If specified, request that the device use this MAC address instead. This is known as MAC cloning or spoofing.
Beside explicitly specifying a MAC address, the special values "preserve", "permanent", "random" and "stable" are supported. "preserve" means not to touch the MAC address on activation. "permanent" means to use the permanent hardware address if the device has one (otherwise this is treated as "preserve"). "random" creates a random MAC address on each connect. "stable" creates a hashed MAC address based on connection.stable-id and a machine dependent key.
If unspecified, the value can be overwritten via global defaults, see manual of NetworkManager.conf. If still unspecified, it defaults to "preserve" (older versions of NetworkManager may use a different default value).
On D-Bus, this field is expressed as "assigned-mac-address" or the deprecated "cloned-mac-address".
When a value is set, either "half" or "full", configures the device to use the specified duplex mode. If "auto-negotiate" is "yes" the specified duplex mode will be the only one advertised during link negotiation: this works only for BASE-T 802.3 specifications and is useful for enforcing gigabits modes, as in these cases link negotiation is mandatory. If the value is unset (the default), the link configuration will be either skipped (if "auto-negotiate" is "no", the default) or will be auto-negotiated (if "auto-negotiate" is "yes") and the local device will advertise all the supported duplex modes. Must be set together with the "speed" property if specified. Before specifying a duplex mode be sure your device supports it.
With #NMSettingWired:cloned-mac-address setting "random" or "stable", by default all bits of the MAC address are scrambled and a locally-administered, unicast MAC address is created. This property allows to specify that certain bits are fixed. Note that the least significant bit of the first MAC address will always be unset to create a unicast MAC address.
If the property is %NULL, it is eligible to be overwritten by a default connection setting. If the value is still %NULL or an empty string, the default is to create a locally-administered, unicast MAC address.
If the value contains one MAC address, this address is used as mask. The set bits of the mask are to be filled with the current MAC address of the device, while the unset bits are subject to randomization. Setting "FE:FF:FF:00:00:00" means to preserve the OUI of the current MAC address and only randomize the lower 3 bytes using the "random" or "stable" algorithm.
If the value contains one additional MAC address after the mask, this address is used instead of the current MAC address to fill the bits that shall not be randomized. For example, a value of "FE:FF:FF:00:00:00 68:F7:28:00:00:00" will set the OUI of the MAC address to 68:F7:28, while the lower bits are randomized. A value of "02:00:00:00:00:00 00:00:00:00:00:00" will create a fully scrambled globally-administered, burned-in MAC address.
If the value contains more than one additional MAC addresses, one of them is chosen randomly. For example, "02:00:00:00:00:00 00:00:00:00:00:00 02:00:00:00:00:00" will create a fully scrambled MAC address, randomly locally or globally administered.
If specified, this connection will only apply to the Ethernet device whose permanent MAC address matches. This property does not change the MAC address of the device (i.e. MAC spoofing).
If specified, this connection will never apply to the Ethernet device whose permanent MAC address matches an address in the list. Each MAC address is in the standard hex-digits-and-colons notation (00:11:22:33:44:55).
If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple Ethernet frames.
The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "802-11-wireless" or "802-3-ethernet".
Specific port type to use if the device supports multiple attachment methods. One of "tp" (Twisted Pair), "aui" (Attachment Unit Interface), "bnc" (Thin Ethernet) or "mii" (Media Independent Interface). If the device supports only one port type, this setting is ignored.
s390 network device type; one of "qeth", "lcs", or "ctc", representing the different types of virtual network devices available on s390 systems.
Dictionary of key/value pairs of s390-specific device options. Both keys and values must be strings. Allowed keys include "portno", "layer2", "portname", "protocol", among others. Key names must contain only alphanumeric characters (ie, [a-zA-Z0-9]).
Currently, NetworkManager itself does nothing with this information. However, s390utils ships a udev rule which parses this information and applies it to the interface.
Identifies specific subchannels that this network device uses for communication with z/VM or s390 host. Like the #NMSettingWired:mac-address property for non-z/VM devices, this property can be used to ensure this connection only applies to the network device that uses these subchannels. The list should contain exactly 3 strings, and each string may only be composed of hexadecimal characters and the period (.) character.
When a value greater than 0 is set, configures the device to use the specified speed. If "auto-negotiate" is "yes" the specified speed will be the only one advertised during link negotiation: this works only for BASE-T 802.3 specifications and is useful for enforcing gigabit speeds, as in this case link negotiation is mandatory. If the value is unset (0, the default), the link configuration will be either skipped (if "auto-negotiate" is "no", the default) or will be auto-negotiated (if "auto-negotiate" is "yes") and the local device will advertise all the supported speeds. In Mbit/s, ie 100 == 100Mbit/s. Must be set together with the "duplex" property when non-zero. Before specifying a speed value be sure your device supports it.
The #NMSettingWiredWakeOnLan options to enable. Not all devices support all options. May be any combination of %NM_SETTING_WIRED_WAKE_ON_LAN_PHY, %NM_SETTING_WIRED_WAKE_ON_LAN_UNICAST, %NM_SETTING_WIRED_WAKE_ON_LAN_MULTICAST, %NM_SETTING_WIRED_WAKE_ON_LAN_BROADCAST, %NM_SETTING_WIRED_WAKE_ON_LAN_ARP, %NM_SETTING_WIRED_WAKE_ON_LAN_MAGIC or the special values %NM_SETTING_WIRED_WAKE_ON_LAN_DEFAULT (to use global settings) and %NM_SETTING_WIRED_WAKE_ON_LAN_IGNORE (to disable management of Wake-on-LAN in NetworkManager).
If specified, the password used with magic-packet-based Wake-on-LAN, represented as an Ethernet MAC address. If %NULL, no password will be required.
Adds a new MAC address to the #NMSettingWired:mac-address-blacklist property.
the MAC address string (hex-digits-and-colons notation) to blacklist
Add an option to the table. If the key already exists, the value gets replaced.
Before 1.32, the function would assert that the key is valid. Since then, an invalid key gets silently added but renders the profile as invalid.
key name for the option
value for the option
Creates a binding between source_property on source and target_property
on target.
Whenever the source_property is changed the target_property is
updated using the same value. For instance:
g_object_bind_property (action, "active", widget, "sensitive", 0);
Will result in the "sensitive" property of the widget #GObject instance to be updated with the same value of the "active" property of the action #GObject instance.
If flags contains %G_BINDING_BIDIRECTIONAL then the binding will be mutual:
if target_property on target changes then the source_property on source
will be updated as well.
The binding will automatically be removed when either the source or the
target instances are finalized. To remove the binding without affecting the
source and the target you can just call g_object_unref() on the returned
#GBinding instance.
Removing the binding by calling g_object_unref() on it must only be done if
the binding, source and target are only used from a single thread and it
is clear that both source and target outlive the binding. Especially it
is not safe to rely on this if the binding, source or target can be
finalized from different threads. Keep another reference to the binding and
use g_binding_unbind() instead to be on the safe side.
A #GObject can have multiple bindings.
the property on source to bind
the target #GObject
the property on target to bind
flags to pass to #GBinding
Creates a binding between source_property on source and target_property
on target, allowing you to set the transformation functions to be used by
the binding.
This function is the language bindings friendly version of g_object_bind_property_full(), using #GClosures instead of function pointers.
the property on source to bind
the target #GObject
the property on target to bind
flags to pass to #GBinding
a #GClosure wrapping the transformation function from the source to the target, or %NULL to use the default
a #GClosure wrapping the transformation function from the target to the source, or %NULL to use the default
Removes all blacklisted MAC addresses.
Compares two #NMSetting objects for similarity, with comparison behavior modified by a set of flags. See the documentation for #NMSettingCompareFlags for a description of each flag's behavior.
a second #NMSetting to compare with the first
compare flags, e.g. %NM_SETTING_COMPARE_FLAG_EXACT
Compares two #NMSetting objects for similarity, with comparison behavior
modified by a set of flags. See the documentation for #NMSettingCompareFlags
for a description of each flag's behavior. If the settings differ, the keys
of each setting that differ from the other are added to results, mapped to
one or more #NMSettingDiffResult values.
a second #NMSetting to compare with the first
compare flags, e.g. %NM_SETTING_COMPARE_FLAG_EXACT
this parameter is used internally by libnm and should be set to %FALSE. If %TRUE inverts the meaning of the #NMSettingDiffResult.
if the settings differ, on return a hash table mapping the differing keys to one or more %NMSettingDiffResult values OR-ed together. If the settings do not differ, any hash table passed in is unmodified. If no hash table is passed in and the settings differ, a new one is created and returned.
Iterates over each property of the #NMSetting object, calling the supplied user function for each property.
user-supplied function called for each property of the setting
This function is intended for #GObject implementations to re-enforce a [floating][floating-ref] object reference. Doing this is seldom required: all #GInitiallyUnowneds are created with a floating reference which usually just needs to be sunken by calling g_object_ref_sink().
Increases the freeze count on object. If the freeze count is
non-zero, the emission of "notify" signals on object is
stopped. The signals are queued until the freeze count is decreased
to zero. Duplicate notifications are squashed so that at most one
#GObject::notify signal is emitted for each property modified while the
object is frozen.
This is necessary for accessors that modify multiple properties to prevent premature notification while the object is still being modified.
Gets a named field from the objects table of associations (see g_object_set_data()).
name of the key for that association
Gets the D-Bus marshalling type of a property. property_name is a D-Bus
property name, which may not necessarily be a #GObject property.
the property of setting to get the type of
Returns the type name of the #NMSetting object
Returns the number of s390-specific options that should be set for this device when it is activated. This can be used to retrieve each s390 option individually using nm_setting_wired_get_s390_option().
Gets a property of an object.
The value can be:
In general, a copy is made of the property contents and the caller is responsible for freeing the memory by calling g_value_unset().
Note that g_object_get_property() is really intended for language bindings, g_object_get() is much more convenient for C programming.
the name of the property to get
return location for the property value
This function gets back user data pointers stored via g_object_set_qdata().
A #GQuark, naming the user data pointer
Returns the s390 device type this connection should apply to. Will be one of 'qeth', 'lcs', or 'ctc'.
Given an index, return the value of the s390 option at that index. indexes are not guaranteed to be static across modifications to options done by nm_setting_wired_add_s390_option() and nm_setting_wired_remove_s390_option(), and should not be used to refer to options except for short periods of time such as during option iteration.
index of the desired option, from 0 to nm_setting_wired_get_num_s390_options() - 1
Returns the value associated with the s390-specific option specified by
key, if it exists.
the key for which to retrieve the value
Return the list of s390 subchannels that identify the device that this connection is applicable to. The connection should only be used in conjunction with that device.
For a given secret, retrieves the #NMSettingSecretFlags describing how to handle that secret.
the secret key name to get flags for
on success, the #NMSettingSecretFlags for the secret
Returns a list of valid s390 options.
The setting argument is unused and %NULL may be passed instead.
Returns the Wake-on-LAN options enabled for the connection
Returns the Wake-on-LAN password. This only applies to %NM_SETTING_WIRED_WAKE_ON_LAN_MAGIC.
Gets n_properties properties for an object.
Obtained properties will be set to values. All properties must be valid.
Warnings will be emitted and undefined behaviour may result if invalid
properties are passed in.
the names of each property to get
the values of each property to get
Checks whether object has a [floating][floating-ref] reference.
Emits a "notify" signal for the property property_name on object.
When possible, eg. when signaling a property change from within the class that registered the property, you should use g_object_notify_by_pspec() instead.
Note that emission of the notify signal may be blocked with g_object_freeze_notify(). In this case, the signal emissions are queued and will be emitted (in reverse order) when g_object_thaw_notify() is called.
the name of a property installed on the class of object.
Emits a "notify" signal for the property specified by pspec on object.
This function omits the property name lookup, hence it is faster than g_object_notify().
One way to avoid using g_object_notify() from within the class that registered the properties, and using g_object_notify_by_pspec() instead, is to store the GParamSpec used with g_object_class_install_property() inside a static array, e.g.:
enum
{
PROP_0,
PROP_FOO,
PROP_LAST
};
static GParamSpec *properties[PROP_LAST];
static void
my_object_class_init (MyObjectClass *klass)
{
properties[PROP_FOO] = g_param_spec_int ("foo", "Foo", "The foo",
0, 100,
50,
G_PARAM_READWRITE);
g_object_class_install_property (gobject_class,
PROP_FOO,
properties[PROP_FOO]);
}
and then notify a change on the "foo" property with:
g_object_notify_by_pspec (self, properties[PROP_FOO]);
the #GParamSpec of a property installed on the class of object.
Gives the name of all set options.
If variant is %NULL, this clears the option if it is set.
Otherwise, variant is set as the option. If variant is
a floating reference, it will be consumed.
Note that not all setting types support options. It is a bug setting a variant to a setting that doesn't support it. Currently, only #NMSettingEthtool supports it.
Like nm_setting_option_set() to set a boolean GVariant.
the value to set.
Like nm_setting_option_set() to set a uint32 GVariant.
the value to set.
Increase the reference count of object, and possibly remove the
[floating][floating-ref] reference, if object has a floating reference.
In other words, if the object is floating, then this call "assumes ownership" of the floating reference, converting it to a normal reference by clearing the floating flag while leaving the reference count unchanged. If the object is not floating, then this call adds a new normal reference increasing the reference count by one.
Since GLib 2.56, the type of object will be propagated to the return type
under the same conditions as for g_object_ref().
Removes the MAC address at index idx from the blacklist.
index number of the MAC address
Removes the MAC address mac from the blacklist.
the MAC address string (hex-digits-and-colons notation) to remove from the blacklist
Remove the s390-specific option referenced by key from the internal option
list.
key name for the option to remove
Releases all references to other objects. This can be used to break reference cycles.
This function should only be called from object system implementations.
Each object carries around a table of associations from strings to pointers. This function lets you set an association.
If the object already had an association with that name, the old association will be destroyed.
Internally, the key is converted to a #GQuark using g_quark_from_string().
This means a copy of key is kept permanently (even after object has been
finalized) — so it is recommended to only use a small, bounded set of values
for key in your program, to avoid the #GQuark storage growing unbounded.
name of the key
data to associate with that key
Sets a property on an object.
the name of the property to set
the value
For a given secret, stores the #NMSettingSecretFlags describing how to handle that secret.
the secret key name to set flags for
the #NMSettingSecretFlags for the secret
Remove a specified datum from the object's data associations, without invoking the association's destroy handler.
name of the key
This function gets back user data pointers stored via
g_object_set_qdata() and removes the data from object
without invoking its destroy() function (if any was
set).
Usually, calling this function is only required to update
user data pointers with a destroy notifier, for example:
void
object_add_to_user_list (GObject *object,
const gchar *new_string)
{
// the quark, naming the object data
GQuark quark_string_list = g_quark_from_static_string ("my-string-list");
// retrieve the old string list
GList *list = g_object_steal_qdata (object, quark_string_list);
// prepend new string
list = g_list_prepend (list, g_strdup (new_string));
// this changed 'list', so we need to set it again
g_object_set_qdata_full (object, quark_string_list, list, free_string_list);
}
static void
free_string_list (gpointer data)
{
GList *node, *list = data;
for (node = list; node; node = node->next)
g_free (node->data);
g_list_free (list);
}
Using g_object_get_qdata() in the above example, instead of g_object_steal_qdata() would have left the destroy function set, and thus the partial string list would have been freed upon g_object_set_qdata_full().
A #GQuark, naming the user data pointer
Reverts the effect of a previous call to
g_object_freeze_notify(). The freeze count is decreased on object
and when it reaches zero, queued "notify" signals are emitted.
Duplicate notifications for each property are squashed so that at most one #GObject::notify signal is emitted for each property, in the reverse order in which they have been queued.
It is an error to call this function when the freeze count is zero.
Convert the setting (including secrets!) into a string. For debugging purposes ONLY, should NOT be used for serialization of the setting, or machine-parsed in any way. The output format is not guaranteed to be stable and may change at any time.
Decreases the reference count of object. When its reference count
drops to 0, the object is finalized (i.e. its memory is freed).
If the pointer to the #GObject may be reused in future (for example, if it is an instance variable of another object), it is recommended to clear the pointer to %NULL rather than retain a dangling pointer to a potentially invalid #GObject instance. Use g_clear_object() for this.
Validates the setting. Each setting's properties have allowed values, and
some are dependent on other values (hence the need for connection). The
returned #GError contains information about which property of the setting
failed validation, and in what way that property failed validation.
the #NMConnection that setting came from, or %NULL if setting is being verified in isolation.
Verifies the secrets in the setting. The returned #GError contains information about which secret of the setting failed validation, and in what way that secret failed validation. The secret validation is done separately from main setting validation, because in some cases connection failure is not desired just for the secrets.
the #NMConnection that setting came from, or %NULL if setting is being verified in isolation.
This function essentially limits the life time of the closure to
the life time of the object. That is, when the object is finalized,
the closure is invalidated by calling g_closure_invalidate() on
it, in order to prevent invocations of the closure with a finalized
(nonexisting) object. Also, g_object_ref() and g_object_unref() are
added as marshal guards to the closure, to ensure that an extra
reference count is held on object during invocation of the
closure. Usually, this function will be called on closures that
use this object as closure data.
#GClosure to watch
Find the #GParamSpec with the given name for an
interface. Generally, the interface vtable passed in as g_iface
will be the default vtable from g_type_default_interface_ref(), or,
if you know the interface has already been loaded,
g_type_default_interface_peek().
any interface vtable for the interface, or the default vtable for the interface
name of a property to look up.
Add a property to an interface; this is only useful for interfaces that are added to GObject-derived types. Adding a property to an interface forces all objects classes with that interface to have a compatible property. The compatible property could be a newly created #GParamSpec, but normally g_object_class_override_property() will be used so that the object class only needs to provide an implementation and inherits the property description, default value, bounds, and so forth from the interface property.
This function is meant to be called from the interface's default
vtable initialization function (the class_init member of
#GTypeInfo.) It must not be called after after class_init has
been called for any object types implementing this interface.
If pspec is a floating reference, it will be consumed.
any interface vtable for the interface, or the default vtable for the interface.
the #GParamSpec for the new property
Lists the properties of an interface.Generally, the interface
vtable passed in as g_iface will be the default vtable from
g_type_default_interface_ref(), or, if you know the interface has
already been loaded, g_type_default_interface_peek().
any interface vtable for the interface, or the default vtable for the interface
Returns the #GType of the setting's class for a given setting name.
a setting name
Creates a new #NMSettingWired object with default values.
Creates a new instance of a #GObject subtype and sets its properties.
Construction parameters (see %G_PARAM_CONSTRUCT, %G_PARAM_CONSTRUCT_ONLY) which are not explicitly specified are set to their default values.
the type id of the #GObject subtype to instantiate
an array of #GParameter
Wired Ethernet Settings