Creates a new #NMSettingBridge object with default values.
The Ethernet MAC address aging time, in seconds.
The Spanning Tree Protocol (STP) forwarding delay, in seconds.
If specified, The MAC address of the multicast group this bridge uses for STP.
The address must be a link-local address in standard Ethernet MAC address format, ie an address of the form 01:80:C2:00:00:0X, with X in [0, 4..F]. If not specified the default value is 01:80:C2:00:00:00.
A mask of group addresses to forward. Usually, group addresses in the range from 01:80:C2:00:00:00 to 01:80:C2:00:00:0F are not forwarded according to standards. This property is a mask of 16 bits, each corresponding to a group address in that range that must be forwarded. The mask can't have bits 0, 1 or 2 set because they are used for STP, MAC pause frames and LACP.
The Spanning Tree Protocol (STP) hello time, in seconds.
If specified, the MAC address of bridge. When creating a new bridge, this MAC address will be set.
If this field is left unspecified, the "ethernet.cloned-mac-address" is referred instead to generate the initial MAC address. Note that setting "ethernet.cloned-mac-address" anyway overwrites the MAC address of the bridge later while activating the bridge. Hence, this property is deprecated.
The Spanning Tree Protocol (STP) maximum message age, in seconds.
Set maximum size of multicast hash table (value must be a power of 2).
Set the number of queries the bridge will send before stopping forwarding a multicast group after a "leave" message has been received.
Set interval (in deciseconds) between queries to find remaining members of a group, after a "leave" message is received.
Set delay (in deciseconds) after which the bridge will leave a group, if no membership reports for this group are received.
Enable or disable sending of multicast queries by the bridge. If not specified the option is disabled.
If no queries are seen after this delay (in deciseconds) has passed, the bridge will start to send its own queries.
Interval (in deciseconds) between queries sent by the bridge after the end of the startup phase.
Set the Max Response Time/Max Response Delay (in deciseconds) for IGMP/MLD queries sent by the bridge.
If enabled the bridge's own IP address is used as the source address for IGMP queries otherwise the default of 0.0.0.0 is used.
Sets bridge's multicast router. Multicast-snooping must be enabled for this option to work.
Supported values are: 'auto', 'disabled', 'enabled' to which kernel assigns the numbers 1, 0, and 2, respectively. If not specified the default value is 'auto' (1).
Controls whether IGMP snooping is enabled for this bridge. Note that if snooping was automatically disabled due to hash collisions, the system may refuse to enable the feature until the collisions are resolved.
Set the number of IGMP queries to send during startup phase.
Sets the time (in deciseconds) between queries sent out at startup to determine membership information.
The setting's name, which uniquely identifies the setting within the connection. Each setting type has a name unique to that type, for example "ppp" or "802-11-wireless" or "802-3-ethernet".
Sets the Spanning Tree Protocol (STP) priority for this bridge. Lower values are "better"; the lowest priority bridge will be elected the root bridge.
Controls whether Spanning Tree Protocol (STP) is enabled for this bridge.
The default PVID for the ports of the bridge, that is the VLAN id assigned to incoming untagged frames.
Control whether VLAN filtering is enabled on the bridge.
If specified, the protocol used for VLAN filtering.
Supported values are: '802.1Q', '802.1ad'. If not specified the default value is '802.1Q'.
Controls whether per-VLAN stats accounting is enabled.
Array of bridge VLAN objects. In addition to the VLANs specified here, the bridge will also have the default-pvid VLAN configured by the bridge.vlan-default-pvid property.
In nmcli the VLAN list can be specified with the following syntax:
$vid [pvid] [untagged] [, $vid [pvid] [untagged]]...
where $vid is either a single id between 1 and 4094 or a range, represented as a couple of ids separated by a dash.
Appends a new vlan and associated information to the setting. The given vlan gets sealed and a reference to it is added.
the vlan to add
Creates a binding between source_property on source and target_property
on target.
Whenever the source_property is changed the target_property is
updated using the same value. For instance:
g_object_bind_property (action, "active", widget, "sensitive", 0);
Will result in the "sensitive" property of the widget #GObject instance to be updated with the same value of the "active" property of the action #GObject instance.
If flags contains %G_BINDING_BIDIRECTIONAL then the binding will be mutual:
if target_property on target changes then the source_property on source
will be updated as well.
The binding will automatically be removed when either the source or the
target instances are finalized. To remove the binding without affecting the
source and the target you can just call g_object_unref() on the returned
#GBinding instance.
Removing the binding by calling g_object_unref() on it must only be done if
the binding, source and target are only used from a single thread and it
is clear that both source and target outlive the binding. Especially it
is not safe to rely on this if the binding, source or target can be
finalized from different threads. Keep another reference to the binding and
use g_binding_unbind() instead to be on the safe side.
A #GObject can have multiple bindings.
the property on source to bind
the target #GObject
the property on target to bind
flags to pass to #GBinding
Creates a binding between source_property on source and target_property
on target, allowing you to set the transformation functions to be used by
the binding.
This function is the language bindings friendly version of g_object_bind_property_full(), using #GClosures instead of function pointers.
the property on source to bind
the target #GObject
the property on target to bind
flags to pass to #GBinding
a #GClosure wrapping the transformation function from the source to the target, or %NULL to use the default
a #GClosure wrapping the transformation function from the target to the source, or %NULL to use the default
Removes all configured VLANs.
Compares two #NMSetting objects for similarity, with comparison behavior modified by a set of flags. See the documentation for #NMSettingCompareFlags for a description of each flag's behavior.
a second #NMSetting to compare with the first
compare flags, e.g. %NM_SETTING_COMPARE_FLAG_EXACT
Compares two #NMSetting objects for similarity, with comparison behavior
modified by a set of flags. See the documentation for #NMSettingCompareFlags
for a description of each flag's behavior. If the settings differ, the keys
of each setting that differ from the other are added to results, mapped to
one or more #NMSettingDiffResult values.
a second #NMSetting to compare with the first
compare flags, e.g. %NM_SETTING_COMPARE_FLAG_EXACT
this parameter is used internally by libnm and should be set to %FALSE. If %TRUE inverts the meaning of the #NMSettingDiffResult.
if the settings differ, on return a hash table mapping the differing keys to one or more %NMSettingDiffResult values OR-ed together. If the settings do not differ, any hash table passed in is unmodified. If no hash table is passed in and the settings differ, a new one is created and returned.
Iterates over each property of the #NMSetting object, calling the supplied user function for each property.
user-supplied function called for each property of the setting
This function is intended for #GObject implementations to re-enforce a [floating][floating-ref] object reference. Doing this is seldom required: all #GInitiallyUnowneds are created with a floating reference which usually just needs to be sunken by calling g_object_ref_sink().
Increases the freeze count on object. If the freeze count is
non-zero, the emission of "notify" signals on object is
stopped. The signals are queued until the freeze count is decreased
to zero. Duplicate notifications are squashed so that at most one
#GObject::notify signal is emitted for each property modified while the
object is frozen.
This is necessary for accessors that modify multiple properties to prevent premature notification while the object is still being modified.
Gets a named field from the objects table of associations (see g_object_set_data()).
name of the key for that association
Gets the D-Bus marshalling type of a property. property_name is a D-Bus
property name, which may not necessarily be a #GObject property.
the property of setting to get the type of
Returns the type name of the #NMSetting object
Gets a property of an object.
The value can be:
In general, a copy is made of the property contents and the caller is responsible for freeing the memory by calling g_value_unset().
Note that g_object_get_property() is really intended for language bindings, g_object_get() is much more convenient for C programming.
the name of the property to get
return location for the property value
This function gets back user data pointers stored via g_object_set_qdata().
A #GQuark, naming the user data pointer
For a given secret, retrieves the #NMSettingSecretFlags describing how to handle that secret.
the secret key name to get flags for
on success, the #NMSettingSecretFlags for the secret
Gets n_properties properties for an object.
Obtained properties will be set to values. All properties must be valid.
Warnings will be emitted and undefined behaviour may result if invalid
properties are passed in.
the names of each property to get
the values of each property to get
Checks whether object has a [floating][floating-ref] reference.
Emits a "notify" signal for the property property_name on object.
When possible, eg. when signaling a property change from within the class that registered the property, you should use g_object_notify_by_pspec() instead.
Note that emission of the notify signal may be blocked with g_object_freeze_notify(). In this case, the signal emissions are queued and will be emitted (in reverse order) when g_object_thaw_notify() is called.
the name of a property installed on the class of object.
Emits a "notify" signal for the property specified by pspec on object.
This function omits the property name lookup, hence it is faster than g_object_notify().
One way to avoid using g_object_notify() from within the class that registered the properties, and using g_object_notify_by_pspec() instead, is to store the GParamSpec used with g_object_class_install_property() inside a static array, e.g.:
enum
{
PROP_0,
PROP_FOO,
PROP_LAST
};
static GParamSpec *properties[PROP_LAST];
static void
my_object_class_init (MyObjectClass *klass)
{
properties[PROP_FOO] = g_param_spec_int ("foo", "Foo", "The foo",
0, 100,
50,
G_PARAM_READWRITE);
g_object_class_install_property (gobject_class,
PROP_FOO,
properties[PROP_FOO]);
}
and then notify a change on the "foo" property with:
g_object_notify_by_pspec (self, properties[PROP_FOO]);
the #GParamSpec of a property installed on the class of object.
Gives the name of all set options.
If variant is %NULL, this clears the option if it is set.
Otherwise, variant is set as the option. If variant is
a floating reference, it will be consumed.
Note that not all setting types support options. It is a bug setting a variant to a setting that doesn't support it. Currently, only #NMSettingEthtool supports it.
Like nm_setting_option_set() to set a boolean GVariant.
the value to set.
Like nm_setting_option_set() to set a uint32 GVariant.
the value to set.
Increase the reference count of object, and possibly remove the
[floating][floating-ref] reference, if object has a floating reference.
In other words, if the object is floating, then this call "assumes ownership" of the floating reference, converting it to a normal reference by clearing the floating flag while leaving the reference count unchanged. If the object is not floating, then this call adds a new normal reference increasing the reference count by one.
Since GLib 2.56, the type of object will be propagated to the return type
under the same conditions as for g_object_ref().
Removes the vlan at index idx.
index number of the VLAN.
Remove the VLAN with range vid_start to vid_end.
If vid_end is zero, it is assumed to be equal to vid_start
and so the single-id VLAN with id vid_start is removed.
the vlan start index
the vlan end index
Releases all references to other objects. This can be used to break reference cycles.
This function should only be called from object system implementations.
Each object carries around a table of associations from strings to pointers. This function lets you set an association.
If the object already had an association with that name, the old association will be destroyed.
Internally, the key is converted to a #GQuark using g_quark_from_string().
This means a copy of key is kept permanently (even after object has been
finalized) — so it is recommended to only use a small, bounded set of values
for key in your program, to avoid the #GQuark storage growing unbounded.
name of the key
data to associate with that key
Sets a property on an object.
the name of the property to set
the value
For a given secret, stores the #NMSettingSecretFlags describing how to handle that secret.
the secret key name to set flags for
the #NMSettingSecretFlags for the secret
Remove a specified datum from the object's data associations, without invoking the association's destroy handler.
name of the key
This function gets back user data pointers stored via
g_object_set_qdata() and removes the data from object
without invoking its destroy() function (if any was
set).
Usually, calling this function is only required to update
user data pointers with a destroy notifier, for example:
void
object_add_to_user_list (GObject *object,
const gchar *new_string)
{
// the quark, naming the object data
GQuark quark_string_list = g_quark_from_static_string ("my-string-list");
// retrieve the old string list
GList *list = g_object_steal_qdata (object, quark_string_list);
// prepend new string
list = g_list_prepend (list, g_strdup (new_string));
// this changed 'list', so we need to set it again
g_object_set_qdata_full (object, quark_string_list, list, free_string_list);
}
static void
free_string_list (gpointer data)
{
GList *node, *list = data;
for (node = list; node; node = node->next)
g_free (node->data);
g_list_free (list);
}
Using g_object_get_qdata() in the above example, instead of g_object_steal_qdata() would have left the destroy function set, and thus the partial string list would have been freed upon g_object_set_qdata_full().
A #GQuark, naming the user data pointer
Reverts the effect of a previous call to
g_object_freeze_notify(). The freeze count is decreased on object
and when it reaches zero, queued "notify" signals are emitted.
Duplicate notifications for each property are squashed so that at most one #GObject::notify signal is emitted for each property, in the reverse order in which they have been queued.
It is an error to call this function when the freeze count is zero.
Convert the setting (including secrets!) into a string. For debugging purposes ONLY, should NOT be used for serialization of the setting, or machine-parsed in any way. The output format is not guaranteed to be stable and may change at any time.
Decreases the reference count of object. When its reference count
drops to 0, the object is finalized (i.e. its memory is freed).
If the pointer to the #GObject may be reused in future (for example, if it is an instance variable of another object), it is recommended to clear the pointer to %NULL rather than retain a dangling pointer to a potentially invalid #GObject instance. Use g_clear_object() for this.
Validates the setting. Each setting's properties have allowed values, and
some are dependent on other values (hence the need for connection). The
returned #GError contains information about which property of the setting
failed validation, and in what way that property failed validation.
the #NMConnection that setting came from, or %NULL if setting is being verified in isolation.
Verifies the secrets in the setting. The returned #GError contains information about which secret of the setting failed validation, and in what way that secret failed validation. The secret validation is done separately from main setting validation, because in some cases connection failure is not desired just for the secrets.
the #NMConnection that setting came from, or %NULL if setting is being verified in isolation.
This function essentially limits the life time of the closure to
the life time of the object. That is, when the object is finalized,
the closure is invalidated by calling g_closure_invalidate() on
it, in order to prevent invocations of the closure with a finalized
(nonexisting) object. Also, g_object_ref() and g_object_unref() are
added as marshal guards to the closure, to ensure that an extra
reference count is held on object during invocation of the
closure. Usually, this function will be called on closures that
use this object as closure data.
#GClosure to watch
Find the #GParamSpec with the given name for an
interface. Generally, the interface vtable passed in as g_iface
will be the default vtable from g_type_default_interface_ref(), or,
if you know the interface has already been loaded,
g_type_default_interface_peek().
any interface vtable for the interface, or the default vtable for the interface
name of a property to look up.
Add a property to an interface; this is only useful for interfaces that are added to GObject-derived types. Adding a property to an interface forces all objects classes with that interface to have a compatible property. The compatible property could be a newly created #GParamSpec, but normally g_object_class_override_property() will be used so that the object class only needs to provide an implementation and inherits the property description, default value, bounds, and so forth from the interface property.
This function is meant to be called from the interface's default
vtable initialization function (the class_init member of
#GTypeInfo.) It must not be called after after class_init has
been called for any object types implementing this interface.
If pspec is a floating reference, it will be consumed.
any interface vtable for the interface, or the default vtable for the interface.
the #GParamSpec for the new property
Lists the properties of an interface.Generally, the interface
vtable passed in as g_iface will be the default vtable from
g_type_default_interface_ref(), or, if you know the interface has
already been loaded, g_type_default_interface_peek().
any interface vtable for the interface, or the default vtable for the interface
Returns the #GType of the setting's class for a given setting name.
a setting name
Creates a new #NMSettingBridge object with default values.
Creates a new instance of a #GObject subtype and sets its properties.
Construction parameters (see %G_PARAM_CONSTRUCT, %G_PARAM_CONSTRUCT_ONLY) which are not explicitly specified are set to their default values.
the type id of the #GObject subtype to instantiate
an array of #GParameter
Bridging Settings